Motorola Radius Software



  1. Motorola Radius M1225 Programming Software

We had a brushfire truck donated to our MAG and it has a dash-mounted Motorola Radius M216 VHF radio. I started looking for programming info on the Ham boards and so far it looks like it requires an old Motorola program that has to be run in DOS. RSS for Motorola GM300 radio, you can program 40 channels to GM300 with this RSS! RSS for Motorola Saber system. RSS for Motorola GM300 professional series, GP300 professional series radio, version 03.01.02. RSS for Motorola CPS06.04AA for HT750/1250/1550 and CDM750/CDM1250/1550 radio, version 06.04. RSS for Motorola HT-800.

Motorola index
Back to Home
An Overview of the
Motorola SM50/SM120
Mobile Radios

By Robert W. Meister WA1MIK

The SM-series (SM50 and SM120) mobile radios are part of the Radius product line. Naturally they have been discontinued and replaced by radios in the CM product line. They are basic low-end radios with models that cover 136-170 MHz and 450-490 MHz, in 10-15 watt and 25-45 watt versions, and narrow (2.5 kHz) and wide (5.0 kHz) bandwidth. The SM50 is two-channel; the SM120 is 16-channel. They are a lot smaller than their MaxTrac/Radius/GM300 cousins, measuring 1-3/4 inches high, 6-5/8 inches wide, and 4-1/4 inches deep. The two-pin power connector is attached to a pigtail piece of wire that sticks out the back of the radio. According to the spec sheet in the service manual, these radios draw about 300mA when idle, 1.5A at maximum receive volume, 7A VHF low power transmit, 8A UHF low power transmit, and 12.5A at 40 watts.

The radios are programmed with their own model-specific DOS software, just like all the other radios in the MaxTrac / Radius / GM300 product lines. Same equipment and environment restrictions apply. The latest version of RSS, HVN9007E, is R05.00.00, dated 01-Sep-98. The MDF file must be hex-edited for out-of-band programming; the SHIFT-NUM trick does not work on the SM50 program. Details can be found at the end of this article.

Note that even though these radios come in narrow-band and wide-band models, the programming software will only allow entry of TX and RX frequencies that are evenly divisible by 5.0 or 6.25 kHz. This means that frequencies such as 155.5000 MHz and 155.5050 MHz are valid but 155.5025 MHz is invalid and will be rejected. I found this out the hard way when programming an SM120 radio for someone.

The SM50 and SM120 probably would not work as well in repeater service as other Motorola products (such as the MaxTrac and Spectra models). They're just not heavy-duty radios. The heat sink of my SM50 gets hot after a 10 minute conversation (50% duty cycle) but not to the point where you'd burn yourself. It also cools off fairly quickly, but remember these radios are only designed for a 5/5/90 duty cycle.

The M1225 radio series seems to have similar model numbers and comes in several channel capacities. It looks very much like a CDM-series radio. This may have been the higher-end companion to the SM50/SM120 radios.

Do yourself a favor: add a dab of white paint or something like 'White-Out' or 'Liquid Paper' in the recessed dot of the volume control knob so you can tell where it's set. I don't know why Motorola paints such an indicator on some knobs but not others. Must be a budget thing.

Model Number Chart:

The model numbers follow the old Motorola 12-character 'standard' scheme, however you can now tell which band-split the radio covers without opening it up and trying to find the part number of the main board (I could not find such a number on any exposed surface of my radio).

The first six characters of the model number are shown below.

Mount TypePowerBandSeries
M always3: 10-25w3: VHF-HIDGC always
4: 25-40w4: UHF

The second six characters are shown below.

Ch. Spacing (kHz)# of ChannelsSplit (MHz)VersionOptions
00: 12.5A: 2 (SM50)1: 136-156A alwaysA always
20: 20/25/30 (VHF)C: 16 (SM120)2: 150-170
20: 20/25 (UHF)2: 450-470
4: 470-490

For example, a 40-watt, UHF, 12.5 kHz spaced, two-channel, 450-470 MHz SM50 radio would have a model number of M44DGC00A2AA.

Common Features (and differences from MaxTrac/Radius/GM300):

The radios can be programmed for high or low power on a mode-by-mode basis. Low power is typically the low end of the power range. Local/Distance can also be programmed on a mode-by-mode basis. The local setting improves intermod rejection by reducing the gain of the receiver's front end. The front panel Option button overrides individual mode settings.

Mode numbers (on 16-channel radios) can be programmed to display 01 thru 99.

Quik-Call II, as well as PL and DPL, are the only available signaling systems. There are no MDC capabilities in these radios.

The 12.5 kHz spaced radios are normally configured for 2.5 kHz total transmitter deviation, but this can be changed (through re-alignment) to 5.0 kHz. The PL level can be set to discrete levels (500 or 750 Hz with the deviation set for 5 kHz).

Even though the 12.5 kHz spaced radio expects narrow-band (2.5 kHz) receive audio, the radio did extremely well when receiving audio with deviations as high at 6 kHz. I measured the receiver audio distortion at several frequencies and found it to be below 5% even with 7 kHz incoming deviation. As far as I can tell, the 12.5 kHz spaced radios ARE type-accepted for narrow-band operation and the service manual specifies narrow filters for both the high (45.1 MHz) and low (455 kHz) IF circuits.

The squelch setting is done through RSS; no squelch pot is present on the board. In fact, there are no tools required, or mechanical adjustments possible, for any alignment procedure. It's all done through the RSS Service menu, like most other Motorola radios that are programmed via a DOS program. My radio would only open the squelch with the alignment value set at 00. Anything higher resulted in a closed squelch. Haikyuu 3ds game rom. The higher it is, the less sensitive the radio will seem to be. Here are the various squelch opening sensitivities by value.

ValdBmuV
1-127.00.100
2-125.00.126
3-123.50.149
4-122.50.168
5-121.50.188
6-121.00.199
7-120.00.224
8-119.00.251
9-118.50.266
10-118.00.282
11-117.00.316
12-116.00.354
13-115.00.398
14-113.00.501
15-111.50.595

There's a 'maximum volume' setting in RSS that affects how loud you can run the receive audio. At full level, it is REALLY loud. I had to turn mine down a bit just so I could run the volume control past 1/2 way.

Both sides of the loudspeaker are driven (like in the GM300, unlike the MaxTrac). You can actually recover usable audio from either speaker lead to ground.

Motorola radius m1225 software

My radio had no problem accepting and operating with 444 MHz frequencies once I hex-edited the MDF file to expand the UHF frequency range (from 450-470 MHz) to 440-480 MHz; see the details below. It also seemed quite happy to control its transmit deviation and output power below 450 MHz. At 444.450 MHz I measured 20dB quieting at -118dBm (0.282uV); at 461.000 MHz I measured 20dB quieting at -119dBm (0.251uV).

A reader inquired whether the SM50 would work down near 440 MHz, so I programmed my radio with 440.000 simplex and 480.000 simplex and tested it out: 40 watts on 440, 38 watts on 480. Sensitivity was -117dBm at these two frequencies, just a bit worse than in the band the radio was designed for.

Differences Between the SM50 and SM120:

The SM50 models are all two-channel (or mode) radios, while the SM120 models are all 16-channel radios. The front panel buttons on the SM50 are marked '1' and '2' and mode LEDs illuminate to tell you which channel is selected: solid green for receive/idle, flashing red for receive/active, and solid red for transmit. The photo below show the SM50 with all indicators identified.

Since everything is back-lit, here's what it looks like in a dark environment with the monitor and option buttons activated. The illuminated silicone buttons can best be described as having a dark 'pink grapefruit juice' color.

The buttons on the SM120 are marked '+' (up) and '-' (down) and a two-digit back-lit LCD display tells you the current channel number (like a MaxTrac/Radius/GM300). The display has additional indicator icons for scan, monitor, and other options.

The SM120 models have scanning capabilities; the SM50 models do not.

The SM50 has a dedicated 'Monitor' button that will place the radio in carrier squelch mode, or open the squelch if held for a few seconds. On the SM120, the button in this position turns scanning on or off, and you would need to program the Option button for the monitor function if you wanted it.

Both radios have a programmable Option button. The table below describes the available functions.

FunctionSM50SM120
Repeat/Talk-aroundYY
Local/DistantYY
Selectable H/LYY
Monitor/VolumeNY
No FunctionYY

Microphone and Microphone Connector:

The standard mike for the SM series is the HMN3174B 'compact' microphone. It's a serviceable black plastic unit (in other words, it has screws in the back and it can be taken apart and fixed) with a red/green LED in the upper right corner (green for receive mode, red for transmit mode) and an RJ45 plug at the end of the coil cord. The LED illumination is controlled directly by the position of the PTT switch in themicrophone; it is NOT a 'receiver unsquelched' indicator.

The SM50/SM120 radios use the same microphones and programming cables as for MaxTrac/Radius/GM300 radios. The MIC jack pins are numbered 1-8 from right to left when looking into the front of the radio with the RJ45 tab down. This matches the other radios listed above.

PinFunctionNotes
1+8VNOT current-limited
2CloneUsed for cloning radios
3HookGround for coded squelch
4Ground
5Mic AudioHas +8VDC bias present
6PTTGround to activate
7SCIBidirectional programming line
8RX AudioFixed level, muted, de-emphasized

Accessory Connector:

These radios use the standard MaxTrac/Radius/GM300 16-pin accessory connector. There's a very nice image of one, complete with pin configuration tables, in the GM300 article elsewhere on this site; you should go find it and read it at some time. I can't force you to read it, but don't come crying to me when you wire it up wrong. The internal loudspeaker is always enabled, so you don't need an accessory plug installed to use the radio. The audio power amplifier provides 7.5 watts of power. It will drive an external speaker very well. The internal speaker is rather small (same as in a MaxTrac/Radius/GM300/GTX radio) and it will distort if the volume is turned up too loud.

There are three preset package configurations: General, Remote, and Phone Patch, but you can customize any of the programmable pins through RSS. The following information was taken from the RSS manual.

General I/O Package Default Configuration
PinFunctionDirectionDebounceActive
4NULLOutputNoLow
8NULLOutputNoLow
9NULLInputNoLow
12NULLInputNoLow
14NULLInputNoLow

The Remote Package Default Configuration is the same as the above table except pin 14 function is 'Mic Off Hook' and pin 14 has Debounce=Yes.

The Phone Patch Package Default Configuration is the same as the above table except pin 8 function is 'PL/DPL & CSQ Detect' and pin 14 has Direction=Output.

Input Functions
FunctionDescription
NULLPin has no function
Mic Off HookIndicates to radio when a remote microphone is off hook
Auto PTTStrips PTT ID and system busy alert tone
RX Audio MuteMutes Rx Audio
Emergency SwitchActivates emergency transmit condition
Output Functions
FunctionDescription
NULLPin has no function
PL/DPL & CSQ DetectPin is active when TPL/DPL and carrier are detected
CSQ DetectPin is active when a carrier is detected by the radio
External AlarmDriver pin for external relay when an Alert is received
Possible Pin Assignments
PinFunction
4 (Output)NULL
PL/DPL & CSQ Detect
CSQ Detect
9 (Input)NULL
Mic Off Hook
Auto PTT
RX Audio Mute
8, 12, 14 (In / Out)Any of the above functions

Looking at the schematic of the radio, I've determined the functionality of each pin on the accessory jack, summarized in the table below. When viewed from the rear of the radio, the top right pin is #1, as indicated on the photo below. A protective rubber plug covers the accessory jack when not in use. In fact, the entire radio is rather well gasketed and weather-resistant.

PinDirectionFunction or Signal Name
1OutExternal Speaker (-) [1]
2InExternal Mic Audio
3InExternal Mic PTT
4OutExternal Alarm / Programmable
5InFlat TX Audio
6Spare
7In/OutGround
8In/OutProgrammable I/O pin
9InEmergency Switch / Programmable [2]
10InIgnition Sense [3]
11OutRX Audio [4]
12In/OutProgrammable I/O pin
13OutSwitched A+
14In/OutProgrammable I/O pin
15InInternal Speaker (+) [5]
16OutExternal Speaker (+) [5]
Notes:
[1]: An external speaker connects to pin 1 and pin 16. Both sides of the speaker are driven. Do not ground either speaker terminal.
[2]: Emergency Switch as an input is not mentioned in the RSS manual.
[3]:Motorola As shipped, Ignition Sense is connected to the incoming A+ line. Removal of an internal 2A fuse will enable Ignition Sense and require A+ on this line.
[4]: RX Audio can be changed via RSS from un-muted / flat, to muted / de-emphasized. No more internal jumper change.
[5]: Pins 15 and 16 are connected internally. The internal speaker is always live. Just unplug it from the main board (inside) to disable it.

Appropriate Manuals:

SM Series Service Manual, covers both VHF and UHF radios, all power levels, SM50 and SM120, p/n 6880903Z45, cost about $24US in October 2009.

Radius SM Series Dealer's Radio Service Software Manual, p/n 6880903Z78, cost about $14US in October 2009. This manual is actually thicker than the service manual, mainly because it has info for a complete newcomer to Motorola programming software, including a tutorial on how to set up a computer, make directories, load software, etc. It easily could have been shortened by 50%. Also, the manual is incomplete in some key areas (service procedures), but since the product has been discontinued and they won't be printing revisions to the manual, it serves no purpose to let Motorola know about such deficiencies.

Opening It Up:

Not much to see under the radio (see photo below).

When I got the radio, I saw the rubber push-button under the chassis, but could not figure out how to get the cover off. It took a few seconds of reading the service manual to find the secret. Remove the volume control knob by pulling straight out, then push and hold the rubber button under the chassis to release the latch beneath it. Hold the chassis with one hand and slide the black plastic cover and front panel forward with the other hand. It comes right off. To reinstall it, line the cover up with the top of the chassis and push the cover backwards until the latch clicks, then replace the volume knob.

There's just one four-layer main board. The top has most of the stuff that would be on the RF board of a MaxTrac (receiver, transmitter, synthesizer) plus the power amplifier. The circuitry underneath is mostly stuff that would be on the Logic board of a MaxTrac (microprocessor and audio processing). A vertically-mounted display board attaches to a connector at the front of the main board. Here's what you can see inside.

Hex-Editing the MDF file:

The SM50.MDF file follows the layout and format of most of the other standard MDF files. There are three pairs of frequencies for each band that specifies the lower and upper limits for the TX, RX, and RSS screen. The location may vary according to the version of software, so it's best to search for the hex values (Intel byte order) rather than for me to tell you to change bytes at specific addresses. Remember to make a backup copy of the MDF file first; better to have it and not need it than to need it and not have it. Select the 'Checksum (16-bit)' routine for the checksum and verify that it's the same after you've finished hex-editing the file.

Search for the four hex byte sequence 94,11,5C,12. You should find three occurrences of these values. The 94,11 corresponds to a decimal value of 4500 and the 5C,12 corresponds to a decimal value of 4700. These are equivalent to 450.0 and 470.0 MHz, which is the normal range for the radio and RSS. Change these three sequences of hex bytes to 30,11,C0,12, which corresponds to decimal values of 4400 and 4800 (440.0 and 480.0 MHz). By simultaneously increasing the value at one location and decreasing the value at another location, the MDF file's checksum remained the same. Save the results and you should be good to go.

There are similar bytes located around the ones above that handle the frequency ranges for VHF and other UHF ranges. They can be similarly changed. Just make sure you increase the upper limit by the same amount you decrease the lower limit, to keep the checksum correct. You can extend the range down to 140.9 and up to 179.1 by replacing the three occurrences of four hex byte sequence DC,05,A4,06 to 81,05,FF,06 but if you need to go further change them to DC,04,A4,07 and that will REALLY open it up.

SM120 Displays 'FF':

After a programming session, the radio displays 'FF' and it won't transmit at all. Cycling the power or rewriting the code plug doesn't fix a thing.

Apparently the 'FF' indicates the radio did not exit programming mode properly. If you hold the '+' and '-' keys at the same time for three seconds, this seems to cause the radio to exit programming mode.

Acknowledgements and Credits:

Information for this article came from direct examination of a 40-watt UHF SM50 radio plus perusal of the above two manuals. I also changed my radio from 2.5 kHz to 5.0 kHz deviation and went through the entire board replacement procedures.

PL, DPL, SM50, SM120, Radius, MaxTrac, GM300, GTX, and a bunch of other terms are trademarks of Motorola, Inc.

Mike WA6ILQ asked several questions, which required additional research and several additions to the article, and also pointed out a couple of errors.

Contact Information:

The author can be contacted at: his-callsign [ at ] comcast [ dot ] net.

Mojang ab minecraft pe 0.15 04. Back to the top of the page
Up one level (Motorola index)
Back to Home

This page originally posted on Saturday 24-Oct-2009.


Photographs, article text, and hand-coded HTML © Copyright2009 by Robert W. Meister WA1MIK.

This web page, this web site, the information presented in and on its pages and in these modifications and conversions is © Copyrighted 1995 and (date of last update) by Kevin Custer W3KKC and multiple originating authors. All RightsReserved, including that of paper and web publication elsewhere.


From The RadioReference Wiki

Also see Batlabs for a good Motorola radio resource!Please be aware that these radios require special programming software that is legally only obtainable from Motorola. Most of them up to the early 2000s also require a RIB (Radio Interface Box) with a radio specific cable; most later models have a radio-specific cable but require no RIB. Back to Motorola page.

The Motorola Direct Talk article has additional information.


SeriesHandheldsMobilesOthers
Genesis
Iden
Jedi
Waris

(PROfessional)

  • CDM1250
  • CDM1550/CDM1550·LS+
Cosmo
EX


Saber
Radius
Spectra/Syntor
XTN
Unknown



APX Multi-Band



FRS

Dispatch Equipment

Model NumberType
MC1000Deskset Controller
MC2000Deskset Controller
MC2500Deskset Controller
MC3000Deskset Controller
MCC 5500Dispatch Console
MCC 7500IP Dispatch Console
MIP 5000VoIP Radio Console
CENTRACOM EliteDispatch Control Center
CommandStar LiteConsole
XTL 5000ASTRO Digital Consolette

Motorola Radios for Sale

Motorola Radius M1225 Programming Software

Retrieved from 'https://wiki.radioreference.com/index.php?title=Motorola_Radios&oldid=264873'